| Deel Nee | Fabrikant | Toepassing |
|---|
| MX7824KCAG | MaximIC | CMOS, high-speed, 8-bit ADC with multiplex. Error (LSB) +-1 |
| MAX4539EPP | MaximIC | Low-voltage, single 8-to-1 calibration multiolexer. |
| MAX792LCPE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 4.62V |
| MAX651C/D | MaximIC | 3.3V or adjustable, high-efficiency, current-limited control scheme, step-down DC-DC controller. |
| MAX6318LHUK33AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.300V min, reset timeout 1ms, typ watchdog timeout 102ms |
| MAX747CSD | MaximIC | High-efficiency, PWM, step-down P-channel DC-DC controller |
| MAX468CWE | MaximIC | Two-channel, quad video buffer. Voltage gain 1V/V. |
| DG305CJ | MaximIC | CMOS dual and quad analog switch. |
| MAX4589CAP | MaximIC | Low-voltage, high-isolation, dual 2-channel RF and video multiplexer. |
| MAX539ACPA | MaximIC | +5V, low-power, voltage-output, serial 12-bit DAC. Error (LSB) +-1/2. 140microA supply current. Flexible output ranges 0V to Vdd. |
| MAX6318MHUK48DX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| ICL7662CBA | MaximIC | CMOS voltage converter |
| MX7828KCWI | MaximIC | CMOS, high-speed, 8-bit ADC with multiplex. Error (LSB) +-1 |
| MAX748ACWE | MaximIC | Step-down, current-mode PWM DC-DC controller. Input voltage range 3.3V to 16V |
| MAX6353MSUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.38V (Vcc5) and 2.93V (Vcc3). Active-low push-pull reset 5V. |
| MAX501BCNG | MaximIC | Voltage-output, 12-bit multiplying DAC. Error(LSBs) +-3/4. |
| MAX8874REUK-T | MaximIC | Low-dropout, 120mA linear regulator with auto-discharge function. Preset output voltage 2.80V. |
| MAX6316LUK48CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX297MJA | MaximIC | 8th-order, lowpass, elliptic, switched-capacitor filter. Clock-tunable corner-freguency range 0.1Hz to 50kHz |
| MAX8211ESA | MaximIC | Microprocessor voltage monitor with programmable voltage detection. Define output current limit. |
| MAX225EWI | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| DG403AZ | MaximIC | Improved, dual, SPDT, two NO and two NC switches, high-speed analog switch. |
| MAX801MEPA | MaximIC | Supervisory circuit with +-1.5% reset accuracy. Reset threshold(typ) 4.425V. Watchdog. |
| MAX6347UR40-T | MaximIC | Microprocessor supervisory circuit (reset output active-high, push-pull). Reset threshold (typ) 4.000V. Order increment 10k |
| MAX1200ACMH | MaximIC | +5V single-supply, 1Msps, 16-bit self-calibrating ADC |
| MAX6316LUK46CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX951C/D | MaximIC | Ultra low-power, single-supply Op Amp + comparator + reference. Internal 1.2V+-2% bandgap reference. Op Amp gain stability 1V/V. Supply current 7microA. |
| MAX465CWG | MaximIC | Two-channel, triple RGB switch and buffer. Voltage gain 2V/V. |
| MAX5150BEEE | MaximIC | Low-power, dual, 13-bit voltage-output DAC with serial interface. +5V single-supply operation. INL(LSB) +-1. |
| MAX3665EUA | MaximIC | 622Mbps, ultra-low-power, 3.3V transimpedance preamplifier for SDH/SONET. |
